Toyota
How to reset oil change light indicator reset maintenance light without using a computer for Toyota
How to reset oil change light indicator reset maintenance light without using a computer for Toyota
1986-88
When “CHECK ENGINE OIL” is displayed on the Super Monitor, press the “SELECT” button below the display until “ENGINE OIL” mode is displayed (unless it already is displayed). Then press and hold the “SET” button until “OK” is displayed.
1991-97
To reset the “OIL CHANGE” light, remove the cover from the switch located below the speedometer. Insert a blunt object and depress the switch.
Toyota 4Runner 2003-onwards
With the ignition “OFF”, press and hold “RESET” button. Turn ignition to the “ON” position. Continue to hold button until “MAINT REQD” light turns off.
Turn ignition off.
Camry 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Corolla
Turn the key to the off position. Press and hold down the trip meter button and turn the key to the “on” position. Continue to hold the trip button for 5 seconds after the key is turned on, then release.
Highlander 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Matrix 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Prius 2004-onwards
With the “POWER” switch off, press and hold “ODO TRIP” button. Press “POWER” switch twice selecting “IG-ON”. Continue to hold button until”000000″ is displayed and “MAINT REQD” light turns off. Turn “POWER” switch to off.
RAV4 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sequoia 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sienna 2004-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Solara 2004-onwards
With the ignition “OFF”, press and hold button to the left of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tacoma 2005-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tundra 2003-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.
1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.