Mercedes Benz Archives - Page 4 of 5 - Reset oil service, maintenance light reset, oilreset

Service oil reset Mercedes Benz CL – Class

2000-2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset button R in the instrument cluster for about 4 seconds. This message appears in the multifunction display “SERVICE INTERVAL? RESET WITH R BUTTON”
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.

2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset button R in the instrument cluster for about 3 seconds. This message appears in the multifunction display “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SECONDS”
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.

Service oil reset Mercedes Benz C-Class

1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001
Turn key in steering lock to position 2.
Call up the trip odometer and main odometer: press either of the lower two buttons on the left hand side of steering wheel until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL?” confirm by pressing R button.
Press and hold the R button on instrument cluster again until signal sounds. Message will res “SERVICE INTERVAL HAS BEEN RESET”.
2002
Switch ignition on.
Repeatedly press the system selection button (bottom button located on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
Repeatedly press the SCROLL FORWARD/BACK button (top button on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
“DO YOU WANT TO RESET THE SERVICE INTERVAL?” appears, confirm that you see the message by holding down the RESET (R) button until you hear a signal.
The reset interval is set.
2003
Turn on the ignition (standard display of the control system appears).
Press SYSTEM button on the multifunction steering wheel until FSS indicator with service symbol and the service deadline appear on display.
Message appears on display “DO YOU WANT TO RESET THE SERVICE INTERVAL?” Confirm by pressing RESET (R) button until you hear a signal (approximately 4 seconds).
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press RESET button for about 3 seconds until this message appears: “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”
To confirm press RESET button until you hear a signal. The service indicator now displays the reset interval.

How to Turn Off the Service Light on a CLK 320

Most models of the Mercedes-Benz CLK 320 are equipped with a service reminder system that displays a notification light on the control panel when service is due. The onboard computer tracks driving conditions to determine when to illuminate the service reminder light. The service technician at the Mercedes-Benz dealer or garage will reset the service light for you when he performs regular maintenance on the car. If you do your own maintenance, you can turn the light off yourself.

1. Turn the ignition switch on. Do not start the engine.

2. Press the information menu button on the left of the steering wheel repeatedly until the total mileage is displayed.

3. Press the up- or down-arrow button on the left of the steering wheel until the service light is displayed.

4. Press and hold the reset button until a confirmation message appears on the display. The reset button is located to the left of the odometer.

5. Press and release the reset button to confirm the reset. The service light turns off.

Service reset Sprinter 2007

Sprinter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.

When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.

Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.

1.Put on ignition

2.Wait for service mileage to revert to vehicle mileage

3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)

4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.

5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.

6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles

service light reset SPRINTER

How to reset the Maintenance Service interval:

Metod 1

– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.

Metod 2

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out

FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)