Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

Use

Reset service light indicator Renault Safrane

Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.

1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
2. Turn ON the ignition, do not start the vehicle.
3. Push reset button until Spanner warning light symbol will start flash.
4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
5. Indicator shows appropriate service interval.
6. Release reset button.
7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.

Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).

Oil Service Reset Audi TT

2000-2004
*Diagnostic Reset Tool Required

Manual Reset using DIS and Reset Knobs:

1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

Manual Reset for 2000 only:

1. Turn off the ignition.
2. Press and hold the TRIP RECORDER reset button on the instrument cluster and turn on the ignition.
3. Release the button. The display will show SERVICE IN —MI or SERVICE.
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2005-2007
1. Turn off the ignition.
2. Press and hold the button to the right of the LCD display in the instrument cluster.
3.Turn the ignition on (do not start the engine); the message “”SERVICE”” appears. Release button.”
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

2008-2012
“Audi recommends the use of a reset tool. *Depening on model

Oil Service Reset BMW Z8

2000-2003
BMW recommends the use of a reset tool.

Manual Reset

1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.

Oil Service Reset BMW Z4

2004-2005
BMW recommends the use of a reset tool.

Manual Reset

1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.

2006-2012
BMW recommends the use of a reset tool.

Manual Reset

1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item. Pressing the button repeatedly will allow the display to scroll through all of the Condition Based Service Items.
4. Press and hold the Instrument Cluster Set/Reset button again and the lower display screen will indicate “”OK”” or “”DUE””.”
5. Pressing the Instrument Cluster Set/Reset button again will allow the “”RESET”” to appear in the lower window for that service. Releasing and reapplying the button one more time will reset the service displayed in the upper window only. ”
6. Turn the ignition off and start the engine to verify the indicator has been reset.

Categories


Copyright © 2013. All Rights Reserved.