Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

start

Reset service light indicator Renault Safrane

Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.

1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
2. Turn ON the ignition, do not start the vehicle.
3. Push reset button until Spanner warning light symbol will start flash.
4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
5. Indicator shows appropriate service interval.
6. Release reset button.
7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.

Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).

Reset service light indicator Renault Scenic 2

Reset service light indicator Renault Scenic 2. From year: 2003, 2004, 2005, 2006, 2007, 2008, 2009.

How to reset service light indicator Renault Scenic 2.

1. Turn the ignition to ON position 2, don’t start the vehicle.
2. On cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster lights.
3. Push & button on the end of the wiper stalk repeatedly until the warning spanner symbol and miles to service appears on the monitor, some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
4. Push & hold the button.
5. The display will now change to the new service interval and start flashing.
6. Keep holding the button until the display stops flashing.
7. Release the button, turn ignition to off and start the car to see if warning light has been reset.

Reset service light indicator Renault Megane 2

Reset service light indicator Renault Megane 2. From year: 2002, 2003, 2004, 2005, 2006, 2007, 2008.

How to reset service light indicator Renault Megane 2.

To reset Service Due Now on a Renault Megane 2, follow these steps:

1. Switch ON the gnition, don’t start the vehicle. For cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster.
2. Push and release the button on the end of the wiper stalk until the Service Due Now message appears on the display. Some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
3. When Service Due Now message is displayed push and hold the same button located at the end of wiper stalk.
4. Now the Service Due now will start to flash after that the display will change to the new service interval and still flashing.
5. Keep holding the button until the display stops flashing.
6. Done, have managed to reset service light indicator Renault Megane 2.

Oil service reset NISSAN GT-R

2009-2011

1. Push the ignition switch to the ON position (do not start the engine). Use the ENTER button (?) and toggle the vehicle information display to show the SETTING screen. Use the NEXT button (?) to select.
2. Use the NEXT button (?) to select MAINTENANCE
i) SETTING > MAINTENANCE > OIL > ENGINE OIL to set or reset the mileage for the engine oil change.
ii) SETTING > MAINTENANCE > FILTER > to set or reset the mileage for the engine oil filter.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset GL – Class

2007-2012

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

Categories


Copyright © 2013. All Rights Reserved.