2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Press and hold the trip reset button with the vehicle stationary and in a power mode less than 6 (two positions before starting engine).
While holding the trip reset button, enter the vehicle into power mode 6 (one position before starting engine).
Release the trip reset button within 10 seconds of entering power mode If the manual reset mode has been successfully entered ‘dISt’ or ‘DATE’ will be displayed in the odometer, depending on which trigger has been activated.
To clear the ‘dISt’ trigger press, and hold the trip reset button for more than 5 seconds within 10 seconds of entering the manual re-set mode. If successful, ‘RESET’ will be displayed in the odometer for 5 seconds. If the date trigger has not been activated ‘END’ will then be displayed in the odometer.
If the date trigger has been activated, ‘DATE’ will be displayed in the odometer. To clear the trigger press and hold the trip reset button for more than 5 seconds within 10 seconds of ‘DATE’ being displayed. If successful, ‘RESET’ will be displayed within the odometer for 5 seconds followed by ‘END’ The odometer will now exit re-set mode.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998-1999
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position O.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
2000-2001
Manual Reset:
Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0.
Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds).
Release button.
Service interval displays the reset interval.
2002-2004
Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0.
Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds).
Release button.
Service interval displays the reset interval.
1997-1999
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position O.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
2000-2002
Manual Reset:
Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0.
Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds).
Release button.
Service interval displays the reset interval.
2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob for about 4 seconds. This message appears in the tachometer: “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY USING RESET BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob for about 4 seconds. This message appears in the tachometer: “SERVICE INTERVAL…RESET: R-BUTTON 3 SEC.”
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.
1997-1999
*Diagnostic Reset Tool Required
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position 0.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
2000-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the right in the instrument cluster for about 2 seconds. This message appears in the multifunction display: “SERVICE INTERVAL? RESET WITH R BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.