Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

odometer reading

Reset service light, maintance on Toyota Land Cruiser

1. Turn your ignition key to the ‘ACC’ or ‘LOCK’ position.
2. Press and hold the trip meter reset nob (next to your Toyota Land Cruiser’s odometer).
3. While holding the trip meter reset nob, turn the ignition to ‘ON’, but do not start your Toyota Land Cruiser.
4. Hold the meter reset until the MAINT REQD light switches off.

If this procedure does not successfully reset your maintenance required light, make sure that your digital odometer is set with the odometer reading showing and try again. If the light is still lit, you can try disconnecting your Toyota Land Cruiser battery, causing the internal computer to reset. If you still haven’t successfully turned off the oil indicator MAINT REQD light, please read your manual or contact your dealer for further instruction!

Reset service light Toyota Yaris 2009 – 2010

1. Turn the ignition to run (one position before starting engine).

2. Ensure odometer reading is shown, turn ignition off.

3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).

4. Hold down knob for at least 5 seconds. The odometer indicates “000000″ and the light goes off. If the system fails to reset, the light will continue flashing.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Toyota 4Runner

2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.

1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Toyota Yaris

2009-2010
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Toyota Tacoma

2005-2008
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2009-2010
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Categories


Copyright © 2013. All Rights Reserved.