Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

distance

Oil service reset SLK – Class

1998-1999
*Diagnostic Reset Tool Required
Manual Reset:

1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required

Manual Reset:

1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.

RESET MAINTENANCE LIGHT ON DODGE SPRINTER

Reset maintenance light on Dodge Sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51″
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Reset maintenance light on dodge sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Categories


Copyright © 2013. All Rights Reserved.