Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

click

Reset the ’07 Porche 911 Carrera Oil Change

Instructions

1. Push inward on the trip odometer reset button and turn the key to the auxiliary position (forward one click from the off position) until “Oil Service Re” or “Oil Service Reset” appears on the odometer screen.

2. Press the odometer reset button a second time until the work “Reset” or “Re” appears on the screen. The word will continuously flash.

3. Press the odometer reset button quickly to complete the reset. “End SIA” appears to indicate a successful reset of the system.

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Service oil reset Chevrolet Caprice

1994
Remove the instrument panel fuse box cover.
Turn the ignition to run (one click before starting).
Press the OIL RESET button for 5 seconds and the change oil lamp should go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1995-1996
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If CHANGE ENGINE OIL light does not go out, turn off the ignition and repeat steps 1-3.
Turn the ignition off and then start the engine to verify the indicator has been reset.

service light reset Audi TT

For Fixed Interval servicing, you can use the following procedure:
Start with the key in, but the ignition turned OFF
Press and hold the button on the right of the display, while turning the ignition one click (to position 1)
Release the button on the right
“SERVICE” should now appear on the display
Press and hold the button on the left of the display until it shows “SERVICE IN xxxx Miles / Kilometres”
Release the left button, then turn off the ignition

service light reset SPRINTER

How to reset the Maintenance Service interval:

Metod 1

– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.

Metod 2

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out

FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Categories


Copyright © 2013. All Rights Reserved.