Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

Volvo

How to reset oil change light indicator reset maintenance light without using a computer for Volvo

Page 1 of 212

Reset Service light for 2006 Volvo XC90

“Resetting the service reminder indicator (SRI), model years 2002-
The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120s each time the ignition is switched on.
Proceed as follows to reset the service reminder indicator (SRI):

1.Ignition position I
2. Press and hold in the reset button for the trip odometer
3. Ignition position II. Note! Turn the key to position II within 2 seconds
4. Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released
5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
6. If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.

Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.”

Reset Service Message Volvo S80

S80

Turn ignition switch to position I
Press and hold “day counter reset button”
Turn ignition to position II
Continue holding day counter for about 10 seconds
While SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted

Reset Service Light Volvo S40, V40

S40 and V40 (1999+)

1. Hold down the odometer button
2. Turn the ignition so all the lights come on
4. Keep holding the odometer down for 30 secs or until the service light starts flashing
5. Release the odometer button while service light flashing
6. Turn off and on again to check

Volvo 850-70 Service Light Reset

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position

How to Reset the Service Light on the Volvo S70

Put the key into the ignition and turn it to position “I.”
Press the trip odometer button in and hold it. Turn the ignition key to position “II.”
Wait about 5 seconds until the service engine light begins to blink. After the 4th blink, turn the ignition key back to position “I.”
Release the button and start the engine. The light should have turned off. If not, repeat steps 1 through 4 again.

Page 1 of 212
Categories





Copyright © 2013. All Rights Reserved.